Overview of 10-Port POE Industrial Ethernet Switch
10-Port POE Industrial Ethernet Switches adopt with high strength IP40 protective housing, industrial EMC design, support wide range redundant power input (48~52V DC) to increase the reliability of communication network. Provide powerful management function that can be managed through a web browser, command line (CLI), and SNMP. It can support 8 ports of 15.4W or 4 ports of 30W at the same time, and the total power can not exceed 245W, which can be used as POE to supply power for other equipment; 0 ~ 2*1000BASE-X SFP interfaces , the optical and electrical combination can be flexibly carried out according to the needs of service ports. It can supply power for IEEE802.3 at / AF compatible powered devices, so it can reduce the additional wiring cost.
| Standard & Protocol |
IEEE 802.3 for 10Base-T IEEE 802.3u for 100Base-TX IEEE 802.3z for 1000Base-X IEEE 802.3x for Flow Control IEEE 802.1Q for VLAN |
| Features |
QoS Setting to improve the quality of the service Port MAC-address learning and statistics Port Enable/Disable, Speed or Mode Setting, Flow control Unicast/Multicast MAC-address Management IGMP Snooping to filter Multicast traffic GMRP Industrial Multicast registration protocol for application in substation Auto-recovery redundant CK-Ring (Full-load failure recovery time < 20ms) Warning by Relay output |
| Management |
Web, CLI and SNMP V1/V2C/V3 Management CLI can login with Telnet and CONSOLE |
| Redundancy Protocol |
CK-Ring, STP/RSTP |
| Interface |
Support IEEE802.3/802.3u/802.3ab/802.3 at/af PoE wiring: Power on unused lines, V+ on pin 4 and 5, V- on pin 7 and 8 (Endspan Mode B) SFP port: 1000M SFP port, 1000M optic fiber or RJ45 Console: RS-232(RJ45 port) Warning: 1 relay, current load DC24V/1A Power: Dual inputs, 2 pluggable four-pins power terminal |
| Serial Port |
Serial Port: RS232 110~115.2Kbps, supports RXD/TXD/GND lines Full-Duplex mode, RS485 supports A/B half-duplex mode RS422/485 Baud rate: 110~115.2Kbps Support ModbusTCP, ModbusRTU protocols Modbus Slave mode supports 12 TCP Master connections |
|
Switching Characteristic |
10M Forward: 14881pps 100M Forward: 148810pps Method: Store and forward Width: 5.6Gbps Cache: 1Mbits MAC: 8K |
|
Power Supply |
Wide DC power input 12~48VDC (12V/24V/48V Typical) Full-load Consumption: < 12W (@24VDC) |
|
Physical Characteristic |
Dimensions(W×H×D): 50mm×150.5mm×125.5mm Weight: 900g Housing: Metal, IP40 protection Installation: Wall mounting or DIN rail mounting |
|
Environment Limits |
Work Temp: -40~85°C Storage Temp: -40~85°C Relative Humidity:5%~95%(non-condensing) |
|
Industrial Standard |
IEC61000-4-2(ESD): ±6KV Contact Discharge, ±15KV Air Discharge IEC61000-4-3(RS): 10V/M (80-1000MHZ) IEC61000-4-4(EFT): Power Cable ±2KV, Data Cable ±2KV IEC61000-4-5(Surge): Power Cable ±1KV CM/±1KV DM, Data Cable: ±1KV IEC61000-4-6(Radio Frequency Conduction): 3V (10KHZ-150KHZ), 10V (150KHZ-80MHZ) IEC61000-4-8（Power Frequency Magnetic Field）：100A/M COUNT 1000A/M，1S TO 3S IEC61000-4-12/18（Oscillating Wave）：2.5KV CM，1KV DM IEC61000-4-10（Damped Oscillation）：30A/M IEC61000-4-16（Common Mode Conduction）：30V COUNT 300V，1S IEC61000-6-2(General Industrial Standards), IEC61850-3(Transformer Substation) IEEE1613(Power Substation) EN50121-4(Rail Transit） |
|
Warranty |
5 years |
|
Available Models |
100M PoE Port |
Fiber Port |
Gigabit SFP Slot |
|
CK2080P |
8 |
— |
— |
|
CK3080P |
8 |
— |
2 |
|
CK6080P |
8 |
— | — |
|
CK7080P |
8 |
— |
2 |
|
Name |
Version |
Date |
|
V1.2 |
2024-08-15 |
